Corghi CompactLine EM 9250 Скачать руководство пользователя страница 47

Страница: 47 / 71

116

EM 9250

Operator’s manual

- use the

keys to search for Unb Gr (or Unb Oun if the ounce display mode

is active)

- press the

key to change the setting:

Unb Gr

to activate the unbalance display in grams

or Unb Oun

to activate the unbalance display in ounces

- press the

key to confirm and exit.

15.4. SET UP -

UNBALANCE ROUNDING-OFF

The machine may be set to display the unbalance values in five-gramme increments i.e.
rounded to the nearest multiple of five (or quarters of an ounce if displayed in ounces)
or rounded to the gram (or tenth of an ounce if displayed in ounces).

Proceed as follows to modify this configuration:

- press the

key

- use the

keys to search for SEt UP

- press the

key to confirm

- use the

keys to search for Gr 5 (if the gram display mode is activated)

or Oun 0.25 (if the ounce display mode is activated)

- press the

key to change the setting:

Gr 1

to activate the unbalance display rounded to the gram

or Gr 5 to activate the unbalance display rounded to the nearest multiple of five

If the ounce display mode is active
or Oun 0.25

to activate the unbalance display rounded to a quarter of an ounce

Oun 0.10

to activate the unbalance display rounded to a tenth of an ounce

- press the

key to confirm and exit.

Содержание CompactLine EM 9250








































































Результаты поиска

Содержание CompactLine EM 9250

Отзывы:

Похожие инструкции для CompactLine EM 9250

Бренды по названию

Популярные бренды

Corghi CompactLine EM 9250, Руководство оператора

Результаты поиска

Содержание CompactLine EM 9250

Отзывы:

Похожие инструкции для CompactLine EM 9250

Бренды по названию

Популярные бренды