background image

EM 9250 

Operator’s manual 

115

UK

- use the 

 

 keys to search for

 SEt UP

- press the 

 key to confirm

- use the 

 

 keys to search for ALU P (or ALU St if previously set)

- press the 

 key to change the setting:

or 

ALU P:

 to activate the ALUP balancing programmes. These programmes are used for 

maximum precision balancing on light aluminium rims that require the application of both 
weights on the same side (inner) in relation to the rim disk. This type of wheel balancer is 
particularly suitable for application of adhesive weights on the rim, thanks to the forward 
position of the wheel in relation to the body, which allows a large zone on the inside of 
the rim to be accessed freely. To enter the dimensions and apply the weights, refer to the 
paragraphs with ALU 1P – ALU2P

or 

ALU St:

 to memorise the rated dimensions of the rim. Self-adhesive weights are gener-

ally used to balance alloy wheels and are applied differently than for standard balancing. 
Several ALU balancing programmes are available, specially designed for these types of rim. 
To enter the dimensions and apply the weights, refer to the paragraphs “Entering wheel 
dimensions (ALU1P and ALU2P programmes excluded)” and “Applying balancing weights”

- press the 

 key to confirm and exit.

15.3. SET UP - UNBALANCE UNIT 

OF MEASURE

The machine may be set to display the unbalance values in grams or ounces. Proceed as 
follows to modify this configuration:

- press the 

 key

- use the 

 

 keys to search for SEt UP

- press the 

 key to confirm

Содержание CompactLine EM 9250








































































Отзывы: