Corghi CompactLine EM 9250 Скачать руководство пользователя страница 48

Страница: 48 / 71

EM 9250

Operator’s manual

117

15.5. SET UP - WARNING OPT

The machine indicates the need to perform an unbalance optimisation procedure (OPT)
with the flashing LED on the display panel.

Proceed as follows to disable this function:

- press the

key

- use the

keys to search for SEt UP

- press the

key to confirm

- use the keys to search for OPt on (OPt oFF if disabled)

- press the

key to change the setting:

OPt on

to activate the display of the alarm indicator light

or OPt oFF

to deactivate the display of the alarm indicator light

- press the

key to confirm and exit.

15.6. SET UP - RIM DIAMETER DISPLAY

UNIT OF MEASUREMENT

The machine may be set to display the rim diameter unit of measurement in inches or
millimetres.
Proceed as follows to modify this configuration:

- press the

key

- use the

keys to search for SEt UP

- press the

key to confirm

- use the

keys to search for -d- in (-d- MM if the display in millimetres

is enabled)

- press the

key to change the setting:

Содержание CompactLine EM 9250








































































Результаты поиска

Содержание CompactLine EM 9250

Отзывы:

Похожие инструкции для CompactLine EM 9250

Бренды по названию

Популярные бренды

Corghi CompactLine EM 9250, Руководство оператора

Результаты поиска

Содержание CompactLine EM 9250

Отзывы:

Похожие инструкции для CompactLine EM 9250

Бренды по названию

Популярные бренды