manualshive.com logo in svg

Coretec VCX-4400-E, Инструкция по установке и эксплуатации

Поделиться
Скачать
Coretec VCX-4400-E Скачать руководство пользователя страница 6

 

Video IP (multi-cast group) 

 

Group Length 

 

FPS (frames per second) 

 

Maximum Bit Rate (encoder only) 

 

Audio On or Off 

 

Com 1 On or Off 

 

Com 1 Bit Rate 

 

Com 1 IP 

 

Com 2 On or Off 

 

Com 2 Bit Rate 

 

Com 2 IP 
 

Mounting

 

the

 

Encoder

 

 

The VCX-4400-E Encoder is a 19-inch wide 1U unit and is furnished with mounting ears 

allowing installation in a 19” rack frame. The VCX-4400-E-H is a desktop like unit that is 8.5 
inches wide and designed to be a shelf model without the need to mounting.  However if you 
choose to mount the half size model, extended mounting ears are available.  The VCX-4400-E-R 
is a single card for use in the multi-card chassis, which is a 19-inch 4U unit that will support 12 
cards.   

All signal connections are from the rear, eliminating any need for setback from the front 

plane of the rack. The user programming port on the front panel is used to alter system 
parameters via a Terminal Program such as HyperTerminal. 
 

Quick

 

Start

 

 

If

 

user

 

wishes

 

to

 

configure

 

settings

 

with

 

VCX4400

­

E

 

via

 

COM

 

Port

 

or

 

Network:

 

Set up for COM Port: 

 

User may configure VCX4400-E setting using a PC connected to the encoder 

control port at the front of the unit. A simple 6-wire phone cable (PCA-2400 
programming cable) with the 

RJ-11 adaptor described in Appendix A

 will supply the 

proper RS-232 connection to the PC’s serial port. 

Note:

 This is not the same as the “Sub-

Channel” interface. Do not use the RJ-11 adaptor for this channel.  
This configuration will permit the unit configuration by a terminal program running on a 
PC. Once you have connected the encoder to the PC’s serial port open your terminal 
program. The encoder will boot up then ask for a password. The default password is: 

admin

. 

 

The PC should have its Com Port configured as: 

Содержание VCX-4400-E







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды