Coretec VCX-4400-E Скачать руководство пользователя страница 31

Страница: 31 / 38

SAP

This command is used to enable or disable the SAP multicast. ON or OFF are the permitted

parameters.

Default: OFF
Example:

SAP ON

SAPAUTHOR

This command is used to set the SDP (RFC-2327) author information. The parameter is an

ASCII string with a limitation of 30 characters.

Default: No text

SAPCOPYRIGHT

This command is used to set the SDP (RFC-2327) copyright information. The parameter is an

ASCII string with a limitation of 30 characters.

Default: No Text

SAPINFO

This command is used to set the SDP (RFC-2327) info information. The parameter is an ASCII

string with a limitation of 62 characters.

Default: Core Tec VCX2400e
Example: SAPINFO Intersection of 1st and main

SAPINTERVAL

This command sets the interval between SAP packet transmissions. The parameter is the number

of milliseconds between transmits.

Default: 5000 ms (5 seconds)
Example: SAPINTERVAL 10000 ms (10 seconds)

SAPIP

This command s

ets the IP address of the destination host for SAP packets. This address is a

multicast address defined in RFC-2974. It is unlikely that the user will need to change this setting.

Default: 224.2.127.254

SAPKEYWORD

This command is used to set the SDP (RFC-2327) keyword information. The parameter is an

ASCII string with a limitation of 30 characters.

Default: No text

SAPNAME

This command is used to set the SDP (RFC-2327) name information. The parameter is an ASCII

string with a limitation of 30 characters.

Default: Core Tec Communications, LLC
Example:

SAPNAME Main Street Camera #1

Содержание VCX-4400-E







































Результаты поиска

Содержание VCX-4400-E

Отзывы:

Бренды по названию

Популярные бренды

Coretec VCX-4400-E, Инструкция по установке и эксплуатации

Результаты поиска

Содержание VCX-4400-E

Отзывы:

Бренды по названию

Популярные бренды