manualshive.com logo in svg

Coretec VCX-4400-E, Инструкция по установке и эксплуатации

Поделиться
Скачать
Coretec VCX-4400-E Скачать руководство пользователя страница 15

The Menu  

 
File Menu 

 
The menu contains selections for 1) File, 2) Options, and 3) Help. The File menu selection 
presents the following drop down menu: 
 

 

 

 
The 

Exit

 option will close the application. The 

Import

 selection is used to select and configure 

VcxNetBurner for a particular firmware update version. Each firmware update will come with an 
import.ini file that contains the necessary information and is accessed though the Import menu 
selection. The import files are normally separate for both the decoder and encoder, and the 
supplied updates should each be stored in a unique directory so that the various update files are 
not overwritten. When the operator selects Import, a file selection dialog will be presented. The 
operator should navigate to the directory were the firmware update is located and the import.ini 
file well be selected by default as shown in the following picture: 
 
 

 

 
 
 
 
After pressing the 

Open

 button the following dialog will be displayed.  

 

Содержание VCX-4400-E







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды