background image

12

CL33600 Series Cylindrical Lock

Copyright © 2009 Corbin Russwin, Inc., an ASSA ABLOY Group company. 

All rights reserved. Reproduction in whole or in part without the 

express written permission of Corbin Russwin, Inc. is prohibited.

Reader LED Configuration
The Harmony Series reader can be configured for (3) modes of LED operation. 
The Access 600 series reader can be configured for (3) modes of LED operation.  
Programming cards are supported to configure the behavior for LED color activity.
Call 1-800-WIRE for details. 
Mode 1:
• Red LED ‘ON’ when powered.
• Presenting a 13.56MHz proximity card will cause LED to ‘FLICKER’ green  
   and return to red state.
• Reference Diagram #1 or #4 as a function of power requirement  
   (12VDC or 24VDC).
   Note: LED wire is unconnected.
Mode 2:
• Green LED “ON” when powered.
• (No Flicker) after presenting valid 13.56MHz proximity card.
• Reference Diagram #2 or #5 as a function of power requirement (12VDC or 24VDC).
   Note: LED wire must be connected to circuit GROUND of the system’s  
   power supply. 

PIN8 (Yellow – LED)

PIN 6 (Blue – RX COM)

PIN 4 (Green – Data 0)

PIN 2 (Red – Reader POS)

PIN 1 (Black – Reader NEG)

PIN 3 (White – Data 1)

PIN 5 (Orange – RX NO)

PIN 7 (Brown - EGND)

PIN 4 (Tan – DPS)

PIN 2 (Gray – Lock POS)

PIN 1 (Violet – Lock NEG)

PIN 3 (Pink – DPS)

Mode 3:
• EAC Panel controls LED operation.
• Reference Diagram #3 or #6 as a function of power requirement (12VDC or 24VDC).
   Note: Control of LED is a function of the EAC panel equipment (ie. relay) to toggle between green and red.
   Note: When LED wire is tied directly into EAC panel relay, no AC signals should be applied on wire or door reader  
   performance will be interfered (refer to Diagram #3 or #6).

6) Wiring Diagrams

Product

8 PIN CONNECTION

4 PIN CONNECTOR

1-Black

2-Red

3-White

4-Green

5-Orange

6-Blue

7-Brown

8-Yellow

9-Violet

10-Gray

11-Pink

12-Tan

ACCESS CONTROL DEVICES: CL33600 TCRNE1 Series M12 - iCLASS ( ElectroLynx wire Color / Function assignments

12 or 24VDC 

Reader Power

WIE-

GAND

WIE-

GAND

RX

RX

EGND

LED

12 OR 24 VDC

(LOCK RELAY

NOT 

USED

NOT 

USED

Corbin Russwin

CL33600 M12

NEG

POS

DATA_1

DATA_0

NO

COM

EGND

REF.
DIA-

GRAMS

NEG

POS

N/A

N/A

Содержание CL33600

















Отзывы: