Contec CONPROSYS nano CPSN-PCB271-S1-041 Скачать руководство пользователя страница 150

Страница: 150 / 155

—

Appendix

—

CPSN-PCB271-S1-041 Reference Manual (Software)

—

150

—

LED

Status of the product is indicated by ON/OFF and flashing of LED.
The meaning of each LED is described below.

Color and Description

LED

Color

Operation

Description

PWR

Green

Initialization is complete.

OFF

Power has not been supplied.

Flashing

Indicates that initialization is in progress.

2 consecutive

flashes

Indicates that an initialization error has occurred.

3 consecutive

flashes

Indicates that a firmware writing error has occurred.

RUN

Green

The device is operating in normal mode.

OFF

The device is operating in recovery mode.

Flashing

Recording medium inserted in USB or microSD card slot is

being accessed.

STS

Green

I/O module is connected.

OFF

I/O module is not connected.

Flashing

I/O module is being accessed.

ERR

Red

It will light up when the error occurs.

I/O module cannot be identified correctly.

An error occurred in accessing the I/O module.

OFF

It indicates the system runs normally.

PWR

RUN

STS

Green All flashing at the

same time

Indicates that firmware and setting files are being written.

PWR

RUN

STS

Green PWR is OFF, RUN

and STS flash

simultaneously

Indicates that the shutdown process is complete.

Содержание CONPROSYS nano CPSN-PCB271-S1-041




























































































































































Результаты поиска

Содержание CONPROSYS nano CPSN-PCB271-S1-041

Отзывы:

Contec CONPROSYS nano CPSN-PCB271-S1-041, Справочное руководство, Страница: 150 / 155

Результаты поиска

Содержание CONPROSYS nano CPSN-PCB271-S1-041

Отзывы: