Contec CNT24-2GY Скачать руководство пользователя страница 8

Страница: 8 / 73

1. Introduction

CNT24-2(USB)GY

Introduction

Summary

Before, the measurement and control was realized by way of inserting PCI interface

boards into expansion slots of a desktop computer in case of configuring system using

computers. However, because of the limit on number of expansion slots, it is difficult

to configure system sometimes, or it is difficult to perform the same measure and

control as PCI interface boards for a note PC. The USB module can be used to resolve

that kind of problems.

CNT24-2(USB)GY is compact isolated up-down counter module which is applied to

USB and can be used easily.

It not only counts high-speed pulses but also can be used for position alignment

control in combination with an encoder. In addition, external electric do not have

direct effect on the host computer because of the isolation between control external

signals and the CPU of the controller module by Optocoupler.

Now serviceable with USB-compatible PCs, this module is best suited for use with

notebook PCs with no PCI bus expansion slot.

When using it on a desktop computer, you can perform simple connection without the

need for opening the host cover.

Corresponding to USB

Desktop Computer

Note PC

Easy to setup
Simple on utilization

Содержание CNT24-2GY










































































Результаты поиска

Содержание CNT24-2GY

Отзывы:

Бренды по названию

Популярные бренды

Contec CNT24-2GY, Руководство пользователя

Результаты поиска

Содержание CNT24-2GY

Отзывы:

Бренды по названию

Популярные бренды