Contec CNT24-2GY Скачать руководство пользователя страница 16

Страница: 16 / 73

1. Introduction

CNT24-2(USB)GY

- Regarding “CE EMC Directive Notice”.

Please see the “Hardware specification” to meet the mentioned standard above.

The ferrite core must be installed in connecting cable so that this product may suit
the above-mentioned standard. And USB connector must be earthed.

Name

Maker

Turn

Quantity

Installation Site

E04SR301334 *

SEIWA

on USB cable at product side

E04SR200917 *

SEIWA

on power cable at product side

* Equivalent product can also be used.

Image diagram

Environment

Use this product in the following environment. If used in an unauthorized

environment, the board may overheat, malfunction, or cause a failure.

Operating temperature

0 - 50°C

Operating humidity

10 - 90%RH (No condensation)

Corrosive gases

None

Floating dust particles

Not to be excessive

Ferrite core

Cable

TURN: 1

TURN: 2

TURN: 4

TURN: 3

Содержание CNT24-2GY










































































Результаты поиска

Содержание CNT24-2GY

Отзывы:

Бренды по названию

Популярные бренды

Contec CNT24-2GY, Руководство пользователя

Результаты поиска

Содержание CNT24-2GY

Отзывы:

Бренды по названию

Популярные бренды