Contec CNT24-2GY Скачать руководство пользователя страница 12

Страница: 12 / 73

1. Introduction

CNT24-2(USB)GY

Support Software

It is suggested that support software produced by our company should be used

according to the goal and development environment.

Windows version of counter input driver

API-CNT(WDM)

[Stored on the bundled disk driver library API-USBP(WDM)]

The API-CNT(WDM) / API-CNT(98/PC) is the Windows version driver library

software that provides products in the form of Win32 API functions (DLL). Various

sample programs such as Visual Basic and Visual C++, etc and diagnostic program

useful for checking operation is provided.

For more details on the supported OS, applicable language and how to download the

updated version, please visit the CONTEC’s Web site

(http://www.contec.com/apipac/).

Accessories (Option)

Isolation counter module (Expansion module for CNT24-2(USB)GY)

: CNT24-2(FIT)GY

AC adapter (input: 90 - 264VAC, output: 5VDC 2.0A)

: POA200-20-2

AC-DC power supply unit (input: 85 - 132VAC, output: 5VDC 3.0A)

: POW-AC13GY

AC-DC power supply unit (input: 85 - 264VAC, output: 5VDC 2.0A)

: POW-AD22GY

DC-DC power supply unit (input: 10 - 30VDC, output: 5VDC 3.0A)

: POW-DD10GY

* Check the CONTEC’s Web site for more information on these options.

Содержание CNT24-2GY










































































Результаты поиска

Содержание CNT24-2GY

Отзывы:

Бренды по названию

Популярные бренды

Contec CNT24-2GY, Руководство пользователя

Результаты поиска

Содержание CNT24-2GY

Отзывы:

Бренды по названию

Популярные бренды