Contec CNT24-2GY Скачать руководство пользователя страница 49

Страница: 49 / 73

5. Troubleshooting

CNT24-2(USB)GY

Q & A

Question

Answer

Can it run on Windows

NT4.0 or Windows 95?

No. In addition, it can not run on Windows 3.1, Windows NT3.51 and so on.

Can it run on OS different

from Windows?

It can not run on non-Windows OS such as Linux, MS-DOS etc.

Can you make an USB

connection with PC-9821

series?

Not support.

How many modules can be

connected to one PC?

The number for connection is namely the number of USB ports available on a

PC. Please supply the power by AC adapter when expending ports by USB

HUB.

Can the developed

applications run on other

PC?

Please install USB driver and set device name for developed applications with

which the files necessary to distribute are supplied. USB driver is in the

INF folder on disk drive.

Does it have license in

distributing developed

applications?

It is free to distribute developed applications.

Can applications be

developed in language

different from

corresponding language?

The languages in which the supplied sample programs are written are the

supported languages. USB driver is supplied in the form of Win32API DLL

and so that it can be used by language and applications supporting this form

(It can not be used by language which do not support corresponding argument

type). The integrity of the operation cannot be guaranteed because we do

not verify the operation.

Can it be used without

programming knowledge?

There are supplied software (Development Environment) for application

development on the disk. Applications are basically developed in

corresponding language, and utility programs can be used to check status if

you only want to monitor I/O status.

Can run with other

applications together

simultaneously?

It is possible because of multiple-thread processing in Windows. Reply from

an application may be very slow because of the high load.

Can expansion modules

with different type be

connected?

No. In the case of using this product, CNT24-2(FIT)GY is the only module to

be connected.

What about the maximum

length of USB cable?

The maximum length is less than 5m according to USB specification. But it

can expand to 6 tiers with 30m long when using USB HUB.

How to get the version of

USB driver?

Run diagnostic program and [Diagnosis ...] to get the version of the driver.

How to upgrade USB

driver to latest edition?

You can download it from following homepage when there is latest edition.

https://contec. com/

How to start the device

manager?

Windows 2000 :

Start Start->Settings->Control Panel->System. Select Hardware and click

on Device Manager.

Does it feature

suspend/resume function?

No. Please set power management for a PC in order to avoid suspension in

operation.

Is AC adapter necessary

when HUB is being used?

It is unnecessary to connect with AC adapter when connecting with a HUB of

self power. (It is necessary when using expansion modules.)

Содержание CNT24-2GY










































































Результаты поиска

Содержание CNT24-2GY

Отзывы:

Бренды по названию

Популярные бренды

Contec CNT24-2GY, Руководство пользователя

Результаты поиска

Содержание CNT24-2GY

Отзывы:

Бренды по названию

Популярные бренды