Contec CNT24-2GY Скачать руководство пользователя страница 50

Страница: 50 / 73

5. Troubleshooting

CNT24-2(USB)GY

Question

Answer

Want to perform the

channels more than the

points being appended by

expansion modules.

The number of expansion modules is 3(4 including the module). When

channels more than this number are wanted, please purchase the necessary

module(s) and expansion accessories.

Is adding points by

expansion modules

different form adding

modules?

When modules are added, the USB ports corresponding to those modules will

be used. For example, channel 0 input of module A, channel 0 input of

module B.

When the expansion modules are added, they can be used in the image based

on the number of points in the USB modules.

For example, in the case of the number of input channels of USB module is 8.

channel 0 input of USB module A, channel 8 input of expansion module B.

Therefore, they can be treated as consecutive points.

In what order should the

USB cable and power

cable be unplugged?

When the module is externally powered, for example, via the AC adapter,

unplug the USB cable first, then unplug the power cable.

Содержание CNT24-2GY










































































Результаты поиска

Содержание CNT24-2GY

Отзывы:

Бренды по названию

Популярные бренды

Contec CNT24-2GY, Руководство пользователя

Результаты поиска

Содержание CNT24-2GY

Отзывы:

Бренды по названию

Популярные бренды