Conductix-Wampfler BridgeGuard Plus Скачать руководство пользователя страница 18

Страница: 18 / 20

BRIDGEGUARD PLUS

MANUAL

SECTION 6 - TROUBLESHOOTING

6.0 Potential issues and solutions are shown below. Contact the factory for additional support. See

Table 14-1.

Issue

Potential Cause

Solution

Loss of signals

Electrical Connections

Inspect the electrical connections to the
sensors and to the control box.

Unable to read output signals

Electric Connection

Inspect the connection to terminal blocks in
control box and to the sensor.

Laser is not on reflector plate

Realign sensor and reflector plate

Sensor not working even when plugged in

Sensor-target misalignment

Check to see if sensor is working by holding
the reflector close to the sensor.

Sensor-target misalignment

If the sensor is working check sensor-target
alignment and make adjustments.

Table 6-1

Содержание BridgeGuard Plus





















Результаты поиска

Содержание BridgeGuard Plus

Отзывы:

Похожие инструкции для BridgeGuard Plus

Бренды по названию

Популярные бренды

Conductix-Wampfler BridgeGuard Plus, Руководство по сборке, установке, эксплуатации и обслуживанию

Результаты поиска

Содержание BridgeGuard Plus

Отзывы:

Похожие инструкции для BridgeGuard Plus

Бренды по названию

Популярные бренды