manualshive.com logo in svg

Comtech EF Data SDM-300L3, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comtech EF Data SDM-300L3 Скачать руководство пользователя страница 90

SDM-300L3 Satellite Modem 

Revision 1 

Front Panel Operation 

MN/SDM300L3.IOM 

 

4–22 

  FUNCTION 

SELECT: 

CONFIGURATION: DEMODULATOR: 

  IF 

LOOP 

BACK 

IF LOOP BACK

OFF

 

 

 
 

IMPORTANT

 

This is a Test Mode.

 

 
Programs the modem for IF loopback operation. When IF loopback is turned on, the 
demodulator input is connected to the modulator output through an internal attenuator 
and the modulator continues to TX a signal. The demodulator is programmed to the same 
frequency as the modulator. When IF loopback is turned off, the demodulator is tuned to 
the previous frequency and is reconnected to the IF input. Refer to Figure 4-5 for a block 
diagram of IF loopback operation. 
 

Note:

 IF loopback nullifies RF loopback. 

 

CUSTOMER

DATA

IBS, IDR or 308-2

INTERFACE

ENCODER/

MODULATOR

TRANSMIT RF

EQUIPMENT

ANTENNA

AC POWER

POWER SUPPLY

MICRO-

COMPUTER

REMOTE SERIAL

INTERFACE

FAULT INDICATORS

RECEIVE RF
EQUIPMENT

DEMODULATOR/

DECODER

SATELLITE MODEM

 

Figure 4-5.  IF Loopback 

Note:

 When IF loopback is turned on, the demodulator is looped back to the modulator inside the modem and the demodulator is 

programmed to the same frequency as the modulator. This test mode will verify the operation of the modem. When IF loopback is 
turned off, the demodulator is programmed back to the previous frequency and is reconnected to the IF input. 

 
 
 

Содержание SDM-300L3

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды