Comtech EF Data SDM-300L3, Инструкция по установке и эксплуатации

Страница: 363 / 408

SDM-300L3 Satellite Modem Revision 1
Remote Control Operation MN/SDM300L3.IOM
A–11
Interface
Coding
Format
Receive Command:
Response:
Status:
Response: <add/ICFR_xxxx'cr'
>add/ICFR_xxxx'cr''lf']
<add/ICFR_'cr'
>add/ICFR_xxxx'cr''lf'] Where: xxxx = AMI, HDB3, or B8ZS.
Transmit
Data Fault Command:
Response:
Status:
Response: <add/TDF_xxxx'cr'
>add/TDF_xxxx'cr''lf']
<add/TDF_'cr'
>add/TDF_xxxx'cr''lf']
Where: xxxx = NONE, DATA, or AIS.
Receive
Data Fault Command:
Response:
Status:
Response: <add/RDF_xxxx'cr'
>add/RDF_xxxx'cr''lf']
<add/RDF_'cr'
>add/RDF_xxxx'cr''lf'] Where: xxxx = NONE, DATA, or AIS.
Interface
Service
Channel
Level Command:
Response:
Status:
Response: <add/ISCL_xxx_snn'cr'
>add/ISCL_xxx_snn'cr''lf']
<add/ISCL_xxx'cr'
>add/ISCL_xxx_snn'cr''lf']
Where:
xxx = TX1, TX2, RX1, or RX2 (service
channel designator).
nnn = -20 to +10 in steps of 1 (service
channel level in dBm).
IDR
Backward
Alarm
Enable Command:
Response:
Status:
Response: <add/BW_xxx_nnn'cr'
>add/BW_xxx_nnn'cr''lf']
<add/BW_xxx'cr'
>add/BW_xxx_nnn'cr''lf'] Where:
xxx = TX1, TX2, TX3, TX4, RX1, RX2, RX3,
or RX4 (backward alarm designator).
nnn = ON or OFF.
Drop Data
Format Command:
Response:
Status:
Response: <add/DDF_xxxxxx'cr'
>add/DDF_xxxxxx'cr''lf']
<add/DDF_'cr'
>add/DDF_xxxxxx'cr''lf']
Where: xxxxxx = T1, T1ESF, T1IBS, E1CCS,
E1CAS, E1IBS, E131TS, T1S, or T1ESFS.
Insert Data
Format Command:
Response:
Status:
Response: <add/IDF_xxxxxx'cr'
>add/IDF_xxxxxx'cr''lf']
<add/IDF_'cr'
>add/IDF_xxxxxx'cr''lf'] Where: xxxxxx = T1, T1ESF, T1IBS, E1CCS,
E1CAS, E1IBS, E131TS, T1S, or T1ESFS.
Insert E1
CRC
Enable Command:
Response:
Status:
Response: <add/ICRC_xxx'cr'
>add/ICRC_xxx'cr''lf']
<add/ICRC_'cr'
>add/ICRC_xxx'cr''lf'] Where: xxx = ON or OFF.
Drop
Channels
Assignment Command:
Response:
Status:
Response: <add/DCA_dd;cc'cr'
>add/DCA_dd;cc'cr''lf']
<add/DCA_dd'cr'
>add/DCA_dd;cc'cr''lf']
Where:
dd = 1 to N (over the satellite drop channel)
N = (Modulator Data Rate) divided by
(64 kbps).
cc = 1 to 24 (terrestrial channel number for
T1 data formats).
cc = 1 to 31 (terrestrial time slot number for
E1 data formats).
Note: This command is not valid when the drop
data format is specified as E1CAS and the
modulator data rate is set to 1920.0 kbps.