Comtech EF Data RC-1170 Скачать руководство пользователя страница 40

Страница: 40 / 94

RC-1170/1270 Redundancy Switch Controllers

Revision 0

Front Panel Operation

3–6

MN-RC-1170/1270

Select: Config: Unit: Common: Current Window Menu

Table 3-6. Select: Config: Unit: Common: Current Window Menu Description

Item

Description

Enable

Use to turn off/on Enable feature.

Range

Use to select the Range percent.

If measured current varies by more than ± x%, as shown in the Range percent setting, an
issue will be identified with the unit.

Use the

◄ ►

arrow keys to select Enable or Range. Press ENTER to continue.

Select: Config: Unit: Unit 1/2/3 Menu

Table 3-7. Select: Config: Unit: Unit 1/2/3 Window Screen

Menu Branch

Function

Current Source

Select Off, 13 V, 18 V. via up/down key press

This can only be changed if the rear panel Bias Control Switch is in the center

position.

Ref

This shows the nominal current as recorded by Calibrate in this screen or as

recorded by the rear panel Calibrate push button.

Calibrate

There is a calibrated reference point for both 13 V and 18 V. Select this and press

“Enter” to set calibration point.

Содержание RC-1170































































































Результаты поиска

Содержание RC-1170

Отзывы:

Похожие инструкции для RC-1170

Бренды по названию

Популярные бренды

Comtech EF Data RC-1170, Инструкция по установке и эксплуатации

Результаты поиска

Содержание RC-1170

Отзывы:

Похожие инструкции для RC-1170

Бренды по названию

Популярные бренды