background image

TECHNICAL DATA

Technical data of the thermostat (transmitter):

— temperature measurement range:  

5 to 35°C

 

 

 

 

 

(in 0.1°C increments)

— adjustable temperature range:    

10 to 30°C

 

 

 

 

 

(in 0.5°C increments)

— temperature measurement accuracy:  

±0.5°C

— selectable switching sensitivity:   

±0.2/±0.3°C

— defrosting temperature:  

 

+7°C

— storage temperature:    

 

-10°C to +60°C

— power supply voltage:    

 

2x1.5 V AA alkaline batteries

 

 

 

 

 

(LR6 type)

— operating frequency:    

 

868.35 MHz

— power consumption:    

 

1.5 mW

— battery lifetime:  

 

 

approx. 1 year

— dimensions:    

 

 

112 x 75 x 45 mm

— weight:  

 

 

 

154 g

— temperature sensor type:  

 

NTC 10 K

Ω

 ±1% at 25°C

Technical data of the receiver unit:

— power consumption:    

 

6W

— power supply voltage:    

 

230V AC, 50Hz

— switchable voltage:  

 

 

24V AC / DC, ÷ 250V AC; 50Hz

— switchable current :  

 

 

6A (2A inductive load)

— transmission distance:   

 

approx. 50 m in open terrain

— weight: 

 

 

 

150g

Total weight of the device: approx. 350 g 
(therholder)

The  COMPUTHERM  Q3  RF  type  thermostat  complies  with  the 
requirements of standards EU EMC89/336/EEC; LVD 73/23/EEC; 

93/68/EEC and R&TTE 1999/5/EC.

Содержание q3rf













Отзывы: