Composite-ARF CARF-Models Sukhoi SU-31 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 20

Composite-ARF CARF-Models Sukhoi SU-31 Скачать руководство пользователя страница 8

CARF-Models Sukhoi SU-31

8

Fuselage pack

Qnt.

Description

8 Allen bolts M4x15mm (for fuel tank tray mounting)
8 Washer, M4 (for fuel tank tray mounting bolts)

4  M4 T-Nuts (for fuel tank tray mounting bolts)
2  Allen bolts M4x15mm (for tail wheel mounting)
2  Washer, M4  (for tail wheel mounting)
4  Allen bolts M6x30mm   (for Engine mounting)
4  Washer, M6 ID x 13mm OD  (for Engine mounting)
4  M6 T-Nuts   (for Engine mounting)
2  Allen bolts M6x60mm   (for wheel mounting)
2  Stop nut M6   (for wheel mounting)
2  Washer, M6 ID x 13mm OD  (for wheel mounting)
6  Allen bolts M6x20mm  ( Landing gear plate)
6  Washer, M6 ID x 20mm ( Landing gear plate)

Wing pack

Qnt.

Description

4  Plastic nut M6
4  Aluminum clevise  M3 (with Pins and E-clips)
4  Nuts, M3
4  All-thread M3 x75 mm (linkages)
4  Brass tube ID3 OD4 x 60mm (to reinforcement the linkages)
4  Ball-link, M3 (linkages)
4  Allen bolt, M3 x 20 (to secure ball-links to aileron horns)
4  Washer, M3 (to fix servos to phenolic plates)
4  Stop nut M3 (to secure ball-links to aileron horns)
8  Sheetmetal screws, Ø 2.9  x 13mm ( for servo hatch

mounting)

28 Sheet metal screw Ø 2.9 x 16 mm (to secure servos)

8  Allen bolt, M3 x 15mm
8  Washer, M3
8  Stop nut M3

«
...
6
7
8
9
10
...
»

Содержание CARF-Models Sukhoi SU-31





















Отзывы:

Нет отзывов