manualshive.com logo in svg

CommScope SYSTIMAX imVision X, Руководство пользователя

Поделиться
Скачать
CommScope SYSTIMAX imVision X Скачать руководство пользователя страница 25

www.commscope.com 

 

User Guide 860633028 

June 2018 

 

 

Page 25 of 30 

© 2018 CommScope, Inc. All Rights Reserved 

Rebooting Using the RESET Button 
After the imVision Controller X has been running for at least several minutes, pushing the RESET button will cause the 
imVision Controller X to reboot. To cause a reboot in this case, push and hold the RESET button for 5 seconds before 
releasing it. To indicate the reboot, the STATUS LED will turn red after a slight delay. 
 
Resetting to Factory Defaults Using the RESET Button 
The RESET button can be used to erase all information in the imVision Controller X and reset all configuration, network and 
security settings to factory defaults. The installed firmware version is not affected by this operation. 
Please use the following procedure: 

1.

 

After the imVision Controller X has been running for at least several minutes, reboot the imVision Controller X by 
pressing the RESET button for 5 seconds before releasing it 

2.

 

Wait at the STATUS LED cycles through red, green, then blue to indicate the boot sequence. 

3.

 

Within 2 minutes after the STATUS LED turns blue, push and hold the RESET button 

4.

 

Wait until the STATUS LED turn red before releasing the RESET button 

 
 
 

Содержание SYSTIMAX imVision X































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды