CommScope ION-U EU L 17EP/17EP Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 66

background image

1. General

Page 12

M0200AJA_ION-U_EU_L_17EP_17EP.docx

User’s Manual for ION

®

-U

Required Distances between the ION-U EU L and Antennas

The table below lists the distance that must be maintained between low power ION-U
Extension Units and antennas. Please also see the requirements listed in the

Antenna

Stmt for ISED

and

Antenne Stmt pour ISDE

on pages 10 and 11.

ION-U Model

Antenna gain
without cable

loss (dBi)

Maximum Distance

FCC

ISED

Meters

Inches

Meters

Inches

ION-U EU L 17EP/17EP

9

.502

19.76

.717

28.23

Equipment Symbols Used / Compliance

Please observe the meanings of the following symbols used in our equipment and the
compliance warnings:

Symbol

Compliance

Meaning / Warning

---

FCC

For industrial (Part 20) signal booster:
WARNING: This is NOT a CONSUMER device. It is
designed for installation by FCC LICENSEES and
QUALIFIED INSTALLERS. You MUST have an FCC
LICENSE or express consent of an FCC Licensee to
operate this device. Unauthorized use may result in
significant forfeiture penalties, including penalties in
excess of $100,000 for each continuing violation.

---

ISED

WARNING:  This  is  NOT  a  CONSUMER  device.  It  is
designed for installation by an installer approved by an
ISED licensee. You MUST have an ISED LICENCE or
the  express  consent  of  an  ISED  licensee  to  operate
this device.
AVERTISSEMENT: Ce produit N’EST PAS un appareil
de  CONSOMMATION.  Il  est  conçu  pour  être  installé
par un installateur approuvé par un titulaire de licence
d’ISDE. Pour utiliser cet appareil, vous DEVEZ détenir
une LICENCE d’ISDE ou avoir obtenu le consentement
exprès d’un titulaire de licence autorisé par ISDE.

CE

To be sold exclusively to mobile operators or
authorized installers

– no harmonized frequency

bands, operation requires license. Intended use: EU
and EFTA countries

Indicates conformity with the RED directive
2014/53/EU and RoHS directive 2011/65/EU.

CE

Indicates

conformity

with

the

RED

directive

2014/53/EU and RoHS directive 2011/65/EU certified
by the notified body no. 0700.

WEEE Recycling

Country specific information about collection and recycling arrangements per the
Waste Electrical and Electronic Equipment (WEEE) Directive and implementing
regulations is available on CommScope’s website.

http://www.commscope.com/About-Us/Corporate-Responsibility-and-Sustainability/Environment/#recycling

«
...
10
11
12
13
14
...
»

Содержание ION-U EU L 17EP/17EP



































































Отзывы:

Нет отзывов

Похожие инструкции для ION-U EU L 17EP/17EP

Бренд: N'oveen Страницы: 24

Бренд: Oster Страницы: 12

Xtendex ST-C5KVM-300

Бренд: NTI Страницы: 16

Бренд: X10 Страницы: 7

Бренд: Digitus Страницы: 8

Бренд: camry Страницы: 68

Бренд: HydraConnect Страницы: 11

Бренд: Kasanova Страницы: 20

Бренд: Brandt Страницы: 43

Бренд: Monnit Страницы: 8

Бренд: Lindy Страницы: 10

Бренд: Concept2 Страницы: 59

Бренд: Hotpoint Страницы: 12

DRIVE REACH OTR FLEET

Бренд: weBoost Страницы: 20

Бренд: weBoost Страницы: 32

Essentials HB11301A

Бренд: Mienta Страницы: 14

Бренд: Duronic Страницы: 76

Бренд: Braun Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды