CommScope ION-U EU L 17EP/17EP Скачать руководство пользователя страница 37

Страница: 37 / 66

4. Commissioning

M0200AJA_ION-U_EU_L_17EP_17EP.docx

User’s Manual for ION

-U

Page 37

4.2.3. Connections

ION-U Low Power EU Connectors/Indicators

Port/Conn

Purpose

Type

LOCAL

RS-232

These connectors are used for external modem
communication with another EU.

DB-9 Female

STATUS

These LEDs provide a visual warning of an alarm
condition. The color of the LED indicates the
severity of the alarm.

LED

CTRL

These connectors are used for external modem
communication with RUs.

DB-9 Male

EXPANSION

RU DL

Path 1/ Path 2

These connectors are used to connect to the DL
Expansion ports of up to two Remote Units.

QMA Female

EXPANSION

RU UL

Path 1/ Path 2

These connectors are used to connect to the UL
Expansion ports of up to two Remote Units.

QMA Female

EXPANSION

EU DL

Path 1/ Path 2

These connectors are used to connect to the DL
Expansion ports of another Extension Unit to
provide an additional band of coverage.

QMA Female

EXPANSION

EU UL

Path 1/ Path 2

These connectors are used to connect to the UL
Expansion ports of another Extension Unit to
provide an additional band of coverage.

QMA Female

MAINS

(Vac/Vdc)

This connector provides the power to RU models
that use standard AC (85 to 265 Vac) or RU
models that use standard DC (-60 to -38 Vdc)
power.

Amphenol C016

Series, 4-Pin

MAINS

(Vdc/100)

This connector provides power to RU models
used in locations where the power drawn on each
cable must be limited to a maximum of 100 VA.

Amphenol C016

Series, 7-Pin

Grounding

Bolts

Ground (earth) bolts for connecting the
mandatory ground cable to the EU.

M6 bolts, hex

nut, & washers

ANT 1 / ANT 2

These connectors are used for transmitting and
receiving signals to and from an antenna or
antenna splitter.

4.3-10

RU IN1 /

RU IN2

These connectors are used for transmitting and
receiving signals to and from the antenna port of
an RU.

4.3-10

EU IN1 /

EU IN2

These connectors are used for transmitting and
receiving signals to and from the antenna port of
an EU.

4.3-10

Содержание ION-U EU L 17EP/17EP



































































Результаты поиска

Содержание ION-U EU L 17EP/17EP

Отзывы:

Похожие инструкции для ION-U EU L 17EP/17EP

Бренды по названию

Популярные бренды

CommScope ION-U EU L 17EP/17EP, Руководство пользователя

Результаты поиска

Содержание ION-U EU L 17EP/17EP

Отзывы:

Похожие инструкции для ION-U EU L 17EP/17EP

Бренды по названию

Популярные бренды