CommScope ION-U EU L 17EP/17EP Скачать руководство пользователя страница 55

Страница: 55 / 66

5. Low Power EU Maintenance

M0200AJA_ION-U_EU_L_17EP_17EP.docx

User’s Manual for ION

-U

Page 55

4. Use a #2 Phillips head or

slotted  screwdriver  to  loosen
the  8  universal  slot/Phillips
captive  power  supply  screws
and  carefully  remove  the
supply.  The  weight  of  the
power

supply

must

supported as you loosen the
screws to prevent damage to
the supply.

figure 5-3 8 EU power supply screws

5. Carefully remove the power

supply  from  the  unit.  Do  not
attempt  to  support  the  weight
of the supply with the attached
input and output cables.

figure 5-4 EU power supply with cables

6. Locate

the

input

cable

connector for the power supply
on the right side of the supply.

7. Loosen the 3 Phillips head

terminal screws and remove
the connector.

figure 5-5 EU power supply input cable

Mains
connector

Loosen 8 universal
slot/Phillips screws

Содержание ION-U EU L 17EP/17EP



































































Результаты поиска

Содержание ION-U EU L 17EP/17EP

Отзывы:

Похожие инструкции для ION-U EU L 17EP/17EP

Бренды по названию

Популярные бренды

CommScope ION-U EU L 17EP/17EP, Руководство пользователя

Результаты поиска

Содержание ION-U EU L 17EP/17EP

Отзывы:

Похожие инструкции для ION-U EU L 17EP/17EP

Бренды по названию

Популярные бренды