CommScope ION-U EU L 17EP/17EP Скачать руководство пользователя страница 56

Страница: 56 / 66

5. Low Power EU Maintenance

Page 56

M0200AJA_ION-U_EU_L_17EP_17EP.docx

User’s Manual for ION

-U

8. Locate the output connector for

the power supply on the left
side of the supply.

9. Loosen the 2 Phillips head

screws and remove the output
connector.

figure 5-6 EU power supply output cable

10. Remove the defective supply.

figure 5-7 EU with power supply removed

11. Replace the defective power

supply  with  the  new  power
supply.
It  is  very  important  to  confirm
that  the replacement  supply is
the  same  type  as  the  original
supply.

The AC, DC, and

Vdc/100 supplies are not
interchangeable.

12. Reconnect the input and output

connectors, and tighten the
associated terminal screws.

figure 5-8 EU with replacement power supply

Содержание ION-U EU L 17EP/17EP



































































Результаты поиска

Содержание ION-U EU L 17EP/17EP

Отзывы:

Похожие инструкции для ION-U EU L 17EP/17EP

Бренды по названию

Популярные бренды

CommScope ION-U EU L 17EP/17EP, Руководство пользователя

Результаты поиска

Содержание ION-U EU L 17EP/17EP

Отзывы:

Похожие инструкции для ION-U EU L 17EP/17EP

Бренды по названию

Популярные бренды