CommScope ION-U EU L 17EP/17EP Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 66

background image

4. Commissioning

M0200AJA_ION-U_EU_L_17EP_17EP.docx

User’s Manual for ION

®

-U

Page 23

4.

Commissioning

Read and observe the health and safety and property damage warnings as well as the
description carefully to avoid mistakes and proceed step-by-step as described.

•

Attention

: Do not operate the Extension Unit without terminating the antenna

connectors. The antenna connectors may be terminated by connecting them to
their respective antennas or to a dummy load.

•

Notice

: Only qualified personnel should carry out the electrical, mechanical,

commissioning, and maintenance activities that require the unit to be powered
on when open.

•

When opening the Extension Unit, do not damage the warranty labels on the

internal devices. The warranty is void if the seals are broken.

•

Ensure that all connections have been performed according to chapter

4.1. Low Power EU Mechanical Installation

4.1.1. Health and Safety for mechanical installation

Read and observe chapter 1.2 Health and Safety

1.

Caution:

Risk of injury by the considerable weight of the unit falling. Ensure there

is adequate manpower to handle the weight of the system.

2.

Caution:

Risk of serious personal injury by equipment falling due to improper

installation. The installer must verify that the supporting surface will safely support
the combined load of the electronic equipment and all attached hardware and
components. The screws and dowels (wall anchors) used should also be
appropriate for the structure of the supporting wall.

4.1.2. Property Damage Warnings for mechanical installation

1.

Attention:

Do not install the unit in a way or at a place where the specifications

outlined in the Environmental and Safety Specifications leaflet of the supplier are
not met.

2.

Attention:

Due to power dissipation, the unit may reach a very high temperature.

Ensure sufficient airflow for ventilation.

3.

Notice:

Exceeding the specified load limits may cause the loss of warranty.

4.

Notice:

When connecting and mounting the cables (RF, optical, mains, ...) ensure

that no water can penetrate into the unit through these cables.

«
...
21
22
23
24
25
...
»

Содержание ION-U EU L 17EP/17EP



































































Отзывы:

Нет отзывов

Похожие инструкции для ION-U EU L 17EP/17EP

Бренд: Waring Страницы: 4

Бренд: Waring Страницы: 36

Бренд: nedis Страницы: 73

Бренд: Grundfos Страницы: 180

Бренд: e+p Страницы: 12

Бренд: Xpresskit Страницы: 13

Бренд: Extron electronics Страницы: 2

Бренд: Kalorik Страницы: 24

Kitchen Wizard DKM9801-DC

Бренд: Dome Страницы: 20

Бренд: Monzana Страницы: 10

Бренд: Samsung Страницы: 15

Бренд: Samsung Страницы: 30

Бренд: Samsung Страницы: 33

Бренд: Samsung Страницы: 31

Бренд: Samsung Страницы: 35

Verizon 4G LTE Network Extender

Бренд: Samsung Страницы: 38

Бренд: Samsung Страницы: 43

Verizon SLS-BU102

Бренд: Samsung Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды