manualshive.com logo in svg

CommScope ION-U EU H 7P/80-85P/17EP/19P DC, Руководство пользователя

Поделиться
Скачать
CommScope ION-U EU H 7P/80-85P/17EP/19P DC Скачать руководство пользователя страница 9

1. General 

 

User’s Manual for ION

®

-U Page 

9

 

3. Notice: 

Installation of this equipment is in full responsibility of the installer, who 

has also the responsibility, that cables and couplers are calculated into the 
maximum gain of the antennas, so that this value, which is filed in the FCC Grant 
and can be requested from the FCC data base, is not exceeded. The industrial 
boosters are shipped only as a naked booster without any installation devices or 
antennas as it needs for professional installation.

 

 

4. Notice: 

For installations which have to comply with

 

FCC/Industry Canada 

requirements:

 

English: 

This device complies with FCC Part 15 and Industry Canada license exempt RSS 
standard(s). Operation is subject to the following two conditions: (1) this device may not 
cause interference, and (2) this device must accept any interference, including 
interference that may cause undesired operation of the device. 
 
This device complies with Health Canada’s Safety Code. The installer of this device 
should ensure that RF radiation is not emitted in excess of the Health Canada’s 
requirement. Information can be obtained at http: 
//www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct-eng.php. 
 
Changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate the equipment. 

 
French: 

Cet appareil est conforme à FCC Partie15 d’Industrie Canada RSS standard exempts de 
licence (s). Son utilisation est soumise à Les deux conditions suivantes: (1) cet appareil 
ne peut pas provoquer d’interférences et (2) cet appareil doit accepter Toute 
interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement 
du dispositif. 
 
Cet appareil est conforme avec Santé Canada Code de sécurité 6. Le programme 
d’installation de cet appareil doit s’assurer que les rayonnements RF n’est pas émis au-
delà de I’exigence de Santé Canada. Les informations peuvent être obtenues: 
http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct-fra.php 
 
Les changements ou modifications non expressément approuvés par la partie 
responsable de la conformité pourraient annuler l'autorité de l'utilisateur à utiliser cet 
équipement. 

 

5. Notice: 

Corresponding local particularities and regulations must be observed. For 

national deviations, please refer to the respective documents included in the 
manual CD that is delivered with the unit.

 

 

 

 

Содержание ION-U EU H 7P/80-85P/17EP/19P DC


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды