manualshive.com logo in svg

CommScope ION-U EU H 7P/80-85P/17EP/19P DC, Руководство пользователя

Поделиться
Скачать
CommScope ION-U EU H 7P/80-85P/17EP/19P DC Скачать руководство пользователя страница 21

4. Commissioning 

 

User’s Manual for ION

®

-U Page 

21

 

3.  Hang the Remote Unit into the upper bracket, insert it into the lower bracket, and 

fasten it to the lower bracket with the M8x25 screws (C), split lock washers (D) 
and washers (E), see chapter 4.2.3. 

 
The maximum diameter of the pole or column must not exceed 120 mm (4.7 inch). 

 

figure 4-5 Pole mounting – max. diameter 

4.2.5.  Pole mounting procedure with brackets 

The pole-mounting kit with brackets includes 

  two mounting brackets (A), two counter brackets (B), four threaded bolts (C), 

flat (F) and split lock (G) washers, hexagon (E) and locking (D) nuts to mount 
the brackets to the pole 

  and two M8x25 screws (H), flat (F) and split lock (G) washers to attach the 

Remote Unit to the bracket. 

 

figure 4-6 Pole mounting – with brackets 

120 m

ax.

Содержание ION-U EU H 7P/80-85P/17EP/19P DC


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды