CommScope ION-U EU H 7P/80-85P/17EP/19P DC Скачать руководство пользователя страница 53

Страница: 53 / 57

6. Maintenance

User’s Manual for ION

-U Page

6.3. Cleaning the Heat Sink

Note:

Read and observe chapter 1.2 Health and Safety as well as the
instructions in chapter 6.1 General

before starting with the replacement

procedure. Then, proceed as follows:

1. Switch off the Remote Unit. Make sure that mains power is disconnected for the

following procedure.

2. Remove the fan cover and fan unit from the Remote Unit as described in chapter

6.2 Replacing the Fan Unit.

Caution

: Risk of injury by flying particles when compressed air is used. Wear

protective clothing, especially protective glasses.

3. Use compressed air (max. 5 bars) to blow out any dust, dirt, or other debris in the

heat sink from back to front.

4. If the dirt cannot be blown out completely and parts of it stick to the ribs of the

heat sink, clean the parts concerned carefully from the front using e.g. a brush.
Take care that the heat sink material is not scratched or damaged.

5. After cleaning the heat sink, remount the fan unit according to chapter 6.2

Replacing the Fan Unit. Then, switch the Remote Unit back on.

Содержание ION-U EU H 7P/80-85P/17EP/19P DC


























































Результаты поиска

Содержание ION-U EU H 7P/80-85P/17EP/19P DC

Отзывы:

Бренды по названию

Популярные бренды

CommScope ION-U EU H 7P/80-85P/17EP/19P DC, Руководство пользователя

Результаты поиска

Содержание ION-U EU H 7P/80-85P/17EP/19P DC

Отзывы:

Бренды по названию

Популярные бренды