manualshive.com logo in svg

CommScope ION-U EU H 7P/80-85P/17EP/19P DC, Руководство пользователя

Поделиться
Скачать
CommScope ION-U EU H 7P/80-85P/17EP/19P DC Скачать руководство пользователя страница 51

6. Maintenance 

 

User’s Manual for ION

®

-U Page 

51

 

6. Maintenance 

6.1. General 

 
Read and observe the notices in chapter 1.2 Health and Safety. 
 

Caution:

 Rotating fans. Risk of injury in operation. Wear tight-fitting clothes and 

disconnect mains before connecting or replacing or cleaning the fan unit. 

Caution: 

The unit reaches high temperature in operation. Risk of burns by hot 

surface. Do not touch the unit before it has sufficiently cooled down. 

Note: 

The Remote Unit does not require preventative maintenance measures. 

Note: 

We recommend checking the cleanliness of the unit and in particular of 
the heat sink / fan(s) at appropriate intervals depending on the degree of 
dust and dirt at the installation site. If necessary, any dusty or dirty areas / 
parts should be cleaned at regular intervals, which also depend on the 
degree of dust and dirt at the installation site. 

Maintenance of the ION-U High Power RUs should be performed by replacing only 
components that are described in this chapter. In order to maintain the warranty, 
avoid unintentional damage to the seals on the modules. 
 

Note: 

When sending back the unit, use appropriate packaging. Use of the 
original packaging for shipping the unit is strongly recommended. 

Note: 

Defective parts should only be replaced by original parts from the 
supplier. All service work performed inside the housing is performed at 
the users own risk. 

Note: 

Ensure the Remote Unit has been disconnected from mains power 
during maintenance. 

Note: 

Label any unlabelled cables before disconnecting them to ensure 
correct reconnection. 

Unless otherwise agreed to in writing by CommScope, CommScope’s general limited 
product warranty (

http://www.commscope.com/Resources/Warranties/

) shall be the 

warranty governing the Remote Units, including the installation, maintenance, usage 
and operation of the Remote Units. 
 

For most maintenance procedures, appropriate tools are required to ensure correct 
handling. All of these tools can be ordered from the supplier.  

Note:  

All Remote Unit screws have a right-hand thread, and are tightened by 
turning the screws clockwise and loosened by turning them counter-
clockwise with an appropriate tool.

 

 

Due to the design of the Remote Unit, the fan unit is the only component that should 
be replaced in the field. Please contact the supplier for replacement of any other 
components. 

Содержание ION-U EU H 7P/80-85P/17EP/19P DC


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды