Comfortflame CGDV32NR (PR)-3 Скачать руководство пользователя страница 6

Test Pressures Equal To or Less Than 

1/2 PSIG (3.5 kPa)

1.  Close equipment shutoff valve (see Fig-

ure 34).

2.  Pressurize supply piping system by either 

opening propane/LP supply tank valve for 

propane/LP gas 

replace or opening main gas 

valve located on or near gas meter for natural 

gas 

fireplace

 or using compressed air.

3.  Check all joints from propane/LP supply 

tank  for  propane/LP  or  gas  meter  for 

natural  gas  to  equipment  shutoff  valve 

(see Figure 35 or Figure 36). Apply non-

corrosive leak detection 

fluid

 to all joints. 

Bubbles forming show a leak. Correct all 

leaks at once.

Open

Closed

Equipment 

Shutoff Valve

Figure 34 - Equipment Shutoff Valve

PRESSURE TESTING FIREPLACE GAS

CONNECTIONS

1.  Open equipment shutoff valve (see Fig-

ure 34).

2.  Open main gas valve located on or near 

gas meter for natural gas or open supply 

tank valve for propane/LP gas.

3.  Make sure control knob of 

fireplace

 is in 

the OFF position.

4.  Check  all  joints  from  equipment  shutoff 

valve to gas valve (see Figure 35 or Figure 

36). Apply  noncorrosive  leak  detection 

fluid

 to all joints. Bubbles forming show a 

leak. Correct all leaks at once.

5.  Light 

fireplace

 (see 

Operation

, page 26). 

Check all other internal joints for leaks.

6.  Turn off 

fireplace

 (see 

To Turn Off Gas to 

Appliance

, page 27).

INSTALLING OPTIONAL WALL

MOUNT SWITCH - GWMS2

1.  Connect  one  terminal  of  25  ft.  wire  for 

wall  switch  to TPTH  terminal  on  valve. 

Connect  remaining  wire  terminal  to TH 

terminal on valve. Make sure that wire ter-

minals are in positions on unit as pictured 

in Figure 37. If wires are not connected as 

shown the switch will not work.

2.  Route 25 ft. wire through openings pro-

vided on sides of burner system to a con-

venient location to mount your switch.

3.  Connect one bare wire end to each of the 

terminals of the GWMS2 wall switch.

4.  Install wall switch and cover in wall.

Figure 35 - Checking Gas Joints for 

Propane/LP Gas Fireplace

Propane/LP 

Supply Tank

Gas Va ve

Equipment Shutoff Valve

Figure 36 - Checking Gas Joints for 

Natural Gas Fireplace

Gas 

Meter

Gas Valve

Equipment Shutoff Valve

Figure 37 - Connecting Wall Switch to 

Control Valve

To Wall 

Switch 

Accessory

FIREPLACE INSTALLATION

Continued

Содержание CGDV32NR (PR)-3











Отзывы: