Comco AccuFlo AF10-E Скачать руководство пользователя страница 7

Страница: 7 / 14

PowderGate® Valve

The PowderGate® Nose and Output Fitting should be replaced after 250,000 cycles. They are both included
in the Tune‐Up Kit.

•

Unscrew the Output Fitting with a ¾" wrench.

•

With pliers, gently pull the worn Nose from shaft.

•

Press on new Nose.

•

Install the new Output Fitting.

•

Connect the tubing with the blue Quicknut.

Tune‐Up Kits

ABRASIVE HOSE

MB1233

POWDERGATE OUTPUT FITTING

MB2560‐x

POWDERGATE NOSE

MB1653

TUNE‐UP KIT MB2247‐x

MB2247‐2

1/4" output fitting

MB2247‐3

3/8" output fitting

PowderGate
Output Fitting

MB2560‐3

MB2560‐4

PowderGate
Nose

MB1653

O‐ring

ST5650‐242

In addition to the tune‐up kit, we also recommend that you keep a back‐up supply of nozzles and orifices to
fit your application.

Содержание AccuFlo AF10-E















Результаты поиска

Содержание AccuFlo AF10-E

Отзывы:

Похожие инструкции для AccuFlo AF10-E

Бренды по названию

Популярные бренды

Comco AccuFlo AF10-E, Руководство по эксплуатации оборудования

Результаты поиска

Содержание AccuFlo AF10-E

Отзывы:

Похожие инструкции для AccuFlo AF10-E

Бренды по названию

Популярные бренды