Comcater COMENDA AC2E Скачать руководство пользователя страница 26

Страница: 26 / 28

instruction for the service people

PROBLEMS

TROUBLE SHOOTING

e)the boiler is not encrusted in any way as to
limit the water flow.

Insufficient rinse temperature

a)make sure that the temperature of the supply
is that prescribed 50/55°C.

b)make sure that the thermostat "ST10" is
adjusted to the correct temperature.

c)make sure that the thermostats "ST10" and
"ST10A" are not faulty

d)make sure that the rinsing nozzles have not
been incorrectly increased or replaced by
another type.

If none of the above reasons appears to be the
cause for the problem, proceed as follows:

Machine with electric heating

Make sure that the circuit breaker "QFE10"
(or QFE11)has not switched off or is faulty.

make sure that the coil of the contactor
"KE10" (or KE11) is not interrupted.

check all sections of the boiler elements
"E10" (or E11).

make sure that the safety thermostat "ST10A"
(or  ST11A)  has  not  operated.  Should  this
have  happened  check  the  reason,  then
reactivate  it  as  well  as  the  circuit  breaker
"QFE10" (and/or QFE11)

Содержание COMENDA AC2E





























Результаты поиска

Содержание COMENDA AC2E

Отзывы:

Похожие инструкции для COMENDA AC2E

Бренды по названию

Популярные бренды

Comcater COMENDA AC2E, Инструкция по эксплуатации

Результаты поиска

Содержание COMENDA AC2E

Отзывы:

Похожие инструкции для COMENDA AC2E

Бренды по названию

Популярные бренды