Comcater COMENDA AC2E Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 28

background image

instruction for the service people

22

ALARMS

The display show:
A2 probe (1...7): temperature over 105°C or probe in short circuit
A3 probe (1...7) not connected

LOADING AND UNLOADING OF THE MACHINE

For the transportation of the machine from the delivery point to the final installation position,
use a fork lift or adequate lifting equipment used by authorised staff. Lift the machine by its
frame, taking care that any protruding parts are not damaged (discharges, wiring etc.).

MACHINE DISMANTLING

At the end of its normal lifetime, the machine has to be taken apart according to the local
regulations in force by separating the components as follows:

•

metal parts: hood, platforms, frames, filters

•

electrical parts: motors, remote control switches, microswitches, wiring

•

plastic parts: racks, connections

•

rubber parts: tubes, sleeves

«
...
20
21
22
23
24
...
»

Содержание COMENDA AC2E





























Отзывы:

Нет отзывов

Похожие инструкции для COMENDA AC2E

Бренд: Sammic Страницы: 48

Бренд: Haier Страницы: 16

Бренд: Gaggenau Страницы: 48

Бренд: Smeg Страницы: 41

Бренд: NEFF Страницы: 52

Бренд: Kärcher Страницы: 24

Бренд: Saturn Страницы: 12

Бренд: Candy Страницы: 57

GE Profile PDW8500J

Бренд: GE Страницы: 2

Бренд: GE Страницы: 12

GE Profile PDW9800N

Бренд: GE Страницы: 2

GE Profile PDW8000G

Бренд: GE Страницы: 2

GE Profile PDW9800JBB

Бренд: GE Страницы: 2

Бренд: GE Страницы: 16

GE Profile PDW8700JBB

Бренд: GE Страницы: 2

GE Profile PDW8600J

Бренд: GE Страницы: 2

GE Profile PDW9200JBB

Бренд: GE Страницы: 2

GE Profile PDWF200

Бренд: GE Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды