Comba Telecom RA-5200 Скачать руководство пользователя

Страница: 65 / 72

INSTALLATION GUIDE FOR RA-5200

RA-5200 QI

Page 64

ENU Status : 1-0-0

4.3.4.3 ALARM INFORMATION

Alarm information is equipment specific.

The alarm parameters include Master Alarm and Channel

Alarm. All alarm information, in general, will be displayed in the right part of the main screen when

clicking on each node of the [Alarm Info.]. Please refer to Reference 0.6.3 OMT v3.20 Software

Product Manual for the specified operation details. Following is the alarm list of RA-5200-D, RA-5200-

O and RA-5200-R.

Alarm name

RA-5200-D

RA-5200-O

RA-5200-R

GSM/DCS/WCDMA Uplink LNA Fault

GSM/DCS/WCDMA DL PA Alarm

GSM/DCS/WCDMA Downlink Input Overload Alarm

Chassis Lock Alarm

MCU Battery Fault Alarm

Optical Receiver Alarm
Optical Transmitter Alarm
Equipment Over Temperature Alarm

Power Supply Down Alarm

Power Supply Fault Alarm

Master-Slave Monitor Link Alarm
External Alarm 1~4

Table 26: Alarm List for RA-5200

Refer to Reference 0.6.3 OMT v3.20 Software Product Manual for the alarm configuration and alarm

levels.

4.3.4.4 PROPERTIES INFORMATION

Properties information is equipment specific. The property parameters include Equipment ID, Chip

Info., Equipment Info., Site Location, Comm. Config. that are equipment specified. All properties

information, in general, will be displayed in the right part of the main screen when clicking on each

node of the [Properties Info.].

There are three separate interfaces for [Properties Info.] group.

Node Name

Description

[Equipment ID]

Displays the site ID and site sub ID of the system

[Firmware Info]

Displays the firmware information of the chip

[Equipment Info]

Displays the equipment information as Equipment Type, Equipment Model

and Equipment Manufacture Serial Number

[Site Location]

Displays the longitude and latitude of the equipment installation site. This

information can be viewed directly when equipment signals are connected

[Comm. Config]

Displays the equipment information in groups of IP address, Phones Code,

Report Config, SMSC Number, etc. The relevant information in these groups

can be inserted by users when equipment signals are connected. MOU

specific

Refer to Reference 0.6.3 OMT v3.20 Software Product Manual for the specific description on

Properties Information.

Содержание RA-5200









































































Результаты поиска

Содержание RA-5200

Отзывы:

Похожие инструкции для RA-5200

Бренды по названию

Популярные бренды

Comba Telecom RA-5200, Руководство по установке

Результаты поиска

Содержание RA-5200

Отзывы:

Похожие инструкции для RA-5200

Бренды по названию

Популярные бренды