Colortronic CTT 1200 Скачать руководство пользователя страница 52

Страница: 52 / 96

Regeneration air filter

Loosen the securing nut on lid of the regeneration air filter.

Remove the lid and regeneration air filter housing.

Loosen the two wing nuts.

Remove the circular grid.

Remove the filter mat.

Blow through the filter mat with compressed air from the inside to the outside,

renew the filter.

Re-install the cleaned/new filter.

Replace the circular grid.

Fasten the two wing nuts on.

Replace the regeneration air filter housing and the lid of the regeneration air filter.

Fasten the securing nut onto the regeneration air filter.

Close the panel.

Never operate the dryer without regeneration air filter.

The dryer can’t be put into operation if the panel is not replaced.

Order number filter mat:

ID 93686

64.10-8255GB01

05/03

CTT 1200

Maintenance 5-6

Содержание CTT 1200

































































































Результаты поиска

Содержание CTT 1200

Отзывы:

Похожие инструкции для CTT 1200

Бренды по названию

Популярные бренды

Colortronic CTT 1200, Руководство по эксплуатации

Результаты поиска

Содержание CTT 1200

Отзывы:

Похожие инструкции для CTT 1200

Бренды по названию

Популярные бренды