Colortronic CTT 1200 Скачать руководство пользователя страница 8

Страница: 8 / 96

1.1. Warnings and symbols

The following warnings and symbols are used in these operating instructions:

This symbol indicates danger to life! Fatal or serious injury is possible if the
corresponding instructions, regulations or warnings are not observed.

This symbol indicates that serious injury is possible if the corresponding
instructions, regulations or warnings are not observed.

This symbol indicates that extensive damage to equipment is possible if
the corresponding instructions, regulations or warnings are not obser-
ved.

This symbol indicates information important for becoming familiar with
the equipment, i.e. technical correlations.

This symbol indicates that a technical term is explained at this point.

64.10-8248GB02

05/03

Dehumidified Air Dryer

General Information 1-2

Содержание CTT 1200

































































































Результаты поиска

Содержание CTT 1200

Отзывы:

Похожие инструкции для CTT 1200

Бренды по названию

Популярные бренды

Colortronic CTT 1200, Руководство по эксплуатации

Результаты поиска

Содержание CTT 1200

Отзывы:

Похожие инструкции для CTT 1200

Бренды по названию

Популярные бренды