Cognex In-Sight 1720 Series Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 56

background image

Specifications

30

Table 5-1: In-Sight 1720 Series Wafer Reader General Specifications

Specification

Description

Vertical mount w/ factory-set 50.0mm working distance.
In-Sight 1721: P/N 800-5865-1; P/N 800-5865-1R (RoHS Compliant)
In-Sight 1722: P/N 800-5865-2; P/N 800-5865-2R (RoHS Compliant)

Configurations

Optional Horizontal Mirror Mount (800-5796-1)

Firmware

In-Sight version 2.90 and later.
Supported Wafer Marks

Standards

SEMI font

SEMI M12, M13, M1.15

IBM font

N/A

OCR

Triple font

N/A

2D

Data Matrix™ (ECC 200, 8 x 32) SEMI T7 and M1.15

Reading Capability

Barcode BC 412 and IBM 412

SEMI T1-95

Job/Program

32MB non-volatile flash memory; unlimited storage via remote network device.

Memory

Image/Processing

32MB SDRAM

Sensor

1/3-inch CCD

Optical Properties

6.0mm diagonal, 4.65 x 4.65

µ

m sq. pixels

Resolution

1024 x 768

Electronic Shutter
Speed

64

µ

s to 33ms; up to 18 frames per second.

Rapid reset, progressive scan (supports partial scan), full-frame integration.
256 gray levels (8 bits/pixel)

Image

Acquisition

Gain controlled by software.
Working Distance: adjustable, w/ factory-set option of 50.0mm (Vertical).
Recommended working distance range: 1 to 80.0mm (Vertical); 1 to 56.0mm (Horizontal).
Illumination Area: 31.0mm (W) x 19.0mm (H) (nominal; depends on lighting Mode).

Lighting/Optics

In-Sight 1721: Red LEDs, 630nm wavelength, with the ability to read bright field and dark field
images. Variable exposure controlled through software. Maximum output power <40
microwatts.
In-Sight 1722: Infrared LEDs, 880nm wavelength, with the ability to read bright field and dark
field images. Variable exposure controlled through software. Maximum output power <60

microwatts.

I/O Trigger

1 opto-isolated, acquisition trigger input.

Remote software commands via Ethernet and RS-232.
None built-in.

Discrete

Inputs

Unlimited inputs when using an Ethernet I/O system.

None built-in.

Discrete Outputs

Unlimited outputs when using an Ethernet I/O system.

Status

LEDs

1 Network Traffic/Network Status, 2 User-Configurable, 1 Power

«
...
40
41
42
43
44
...
»

Содержание In-Sight 1720 Series

























































Отзывы:

Нет отзывов

Похожие инструкции для In-Sight 1720 Series

Бренд: Wallenstein Страницы: 31

Бренд: Gates Underwater Products Страницы: 49

Бренд: Gates Underwater Products Страницы: 45

Бренд: oliser Страницы: 6

Бренд: Vaillant Страницы: 80

SmartSensor Matrix

Бренд: Wavetronix Страницы: 2

Бренд: Watt Stopper Страницы: 8

Maintenence Kits

Бренд: Generac Power Systems Страницы: 1

PowerBlade PBH-1540

Бренд: Swisher Страницы: 2

FLEXTRAC Series

Бренд: QC Conveyors Страницы: 32

Бренд: WABCO Страницы: 32

Бренд: R-Biopharm Страницы: 24

Бренд: TREND Страницы: 19

Бренд: QC Conveyors Страницы: 32

Бренд: Defy Страницы: 48

Бренд: A&D Страницы: 10

Бренд: Sacred Sun Страницы: 27

Бренд: CICLOSPORT Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды