background image

Congratulations on having purchased a coemar product. You have assured yourself of a fixture of the highest quality, both in compo-
nentry and in the technology used. We renew our invitation to you to complete the service information on the previous page, to expe-
dite any request for service information or spares (in case of problems encountered either during, or subsequent to, installation). This
information will assist in providing prompt and accurate advice from your coemar service centre.

Following the instructions and procedures outlined in this manual will ensure the maximum efficiency of this product for years to come.

1.1. Packaging

Open the packaging and ensure that no part of the equipment has suffered damage in transit. In case of damage to the equipment,
contact your carrier immediately by telephone or fax, following this with formal notification in writing.

Packing list

Ensure tha packaging contains:

1 Panorama Power MK2
1 Instruction manual
4 Diffusion filters

1.2. Transportation

The 

Panorama Power MK2

should be transported in its original packaging or in an appropriate flight case.

2.1. Important safety information

Fire prevention:

1.

Panorama Power MK2

utilises two 

Philips MSR 575/2

or 

575 MSD lamps

; the use of any alternative lamp is not recommended

and will null and void the fixture’s warranty.

2.

Never locate the fixture on any flammable surface.

3.

Minimum distance from flammable materials: 0,5 m.

4.

Minimum distance from the closest illuminable surface: 2 m.

5.

Replace any blown or damaged fuses only with those of identical values. Refer to the schematic diagram if there is any doubt.

6.

Connect the projector to mains power via a thermal magnetic circuit breaker.

Preventing electric shock:

1.

High voltage is present in the internals of the unit. Isolate the projector from mains supply prior to performing any function which
involves touching the internals of the unit, including lamp replacement.

2.

For mains connection, adhere strictly to the guidelines outlined in this manual.

3.

The level of technology inherent in the 

Panorama Power MK2

requires the use of specialised personnel for all service applications;

refer all work to your authorised coemar service centre.

4.

A good earth connection is essential for proper functioning of the projector.

5.

Mains cables should not come into contact with other cables.

6.

Do not operate the projector with wet hands.

Safety:

1.

The projector should always be installed with bolts, clamps, and other fixings which are suitably rated to support the weight of the
unit.

2.

Always use a secondary safety chain of a suitable rating to sustain the weight of the unit in case of the failure of the primary fixing
point.

3.

Never install the fixture in an enclosed area lacking sufficient air flow; the ambient temperature should not exceed 35°C.

4.

The external surface of the unit, at various points, may exceed 150°C. Never handle the unit until at least 10 minutes have elapsed
since the lamp was turned off.

5.

Always replace the lamp if any physical damage is evident.

6.

A hot lamp may explode. Wait at least 10 minutes after the unit has been turned off prior to attempting to replace the lamp.

7.

The proejctor contains electronic and electrical components which should under no circumstances be exposed to contact with water,
oil or any other liquid. Failure to do so will compromise the proper functioning of the projector.

Protection against ultraviolet radiation:

1.

Never turn on the lamp if any of the lenses, filters, or the aluminium housing is damaged; their respective functions will only operate effi-
ciently if they are in perfect working order. 

2. 

Never look directly into the lamp when it is operating.

Forced ventilation

You will note several air vents on the body of the projector. To avoid any problems associated with overheating, never obstruct any of
these vents as this may seriously compromise the proper operation of the unit.

Protection rating against penetration by external agents:

1. 

The fixture has a protection rating of 

IP 44

; this indicates that it is protected against showers and solid particles larger that 1 mm.

Due to this rating, the fixture may be used in locations exposed to inclement weather.

2. General information

1. Packaging and transportation

English

4

Содержание Panorama Power MK2






























Отзывы: