background image

Code 3 is a registered trademark of Public Safety Equipment, Inc.
3M is a registered trademark of 3M Company Inc.

Public Safety Equipment (UK), Ltd.

Public Safety Equipment, Inc.

Oldham Road, Rishworth

10986 N. Warson Road

Halifax, West Yorkshire—ENGLAND HX6 4QG

St. Louis, Missouri 63114-2029—USA

Ph. 0422-824640   Fax 0422-824604

Ph. (314) 426-2700  Fax (314) 426-1337

Revision 3, 09/97- Instruction Book Part No. 3778

©1997 Public Safety Equipment, Inc. Printed in USA

WARRANTY

This product was tested and found to be operational at the time of manufacture. Provided this product is

installed and operated in accordance with the manufacturer's recommendations, Public Safety Equipment
guarantees all parts and components except the lamps for a period of 1 year from the date of purchase or
delivery, whichever is later. Units demonstrated to be defective within the warranty period will be repaired or
replaced at the factory service center at no cost.

Use of a lamp or other electrical load of a wattage higher than installed or recommended by the factory,

or use of inappropriate or inadequate wiring or circuit protection causes this warranty to become void. Failure
or destruction of the product resulting from abuse or unusual use and/or accidents is not covered by this
warranty.

PSE shall in no way be liable for other damages including consequential, indirect or special damages

whether loss is due to negligence or breach of warranty.

PSE MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY INCLUDING, WITHOUT LIMITA-

TION, WARRANTIES OF FITNESS OR MERCHANTABILITY, WITH RESPECT TO THIS PRODUCT.

PRODUCT RETURNS

In order to provide you with faster service, if you are going to return a product for repair or replacement*,

please contact our factory to obtain a Return Goods Authorization Number (RGA number) before you ship the
product to PSE.  Write the RGA number clearly on the package near the mailing label.  Be sure you use
sufficient packing materials to avoid damage to the product being returned while in transit.

*PSE reserves the right to repair or replace product at its discretion.  PSE assumes no responsibility or liability for expenses

incurred for the removal and/or reinstallation of products requiring service and/or repair.

WWW.CODE3PSE.COM

PROBLEMS OR QUESTIONS? CALL OUR TECHNICAL ASSISTANCE HOTLINE (314) 996-2800

Содержание FM100C









Отзывы: