Cobra Y173V страница 54 Скачать руководство пользователя

Страница: 54 / 66

4. DISASSEMBLING AND SERVICING

VALVE LAPPING TOOL

Use the 32°-45°cutters to narrow and adjust the valve seat so that it contacts the middle of

the valve face. The 32°cutter removes material from the top edge (contact too high).

The 45°cutter removes material from the bottom edge (contact too low). Be sure that the

width of the finished valve seat is within specification.

Standard

Service limit

0.8mm

2.0mm

Make alight pass with the 45°cutter to remove any possible burrs at the edges of the seat.

After resurfacing seat, inspect for even valve seating width. Apply colorant to the valve

tapered face, insert the valve and press it forcefully several times, be sure the valve does not

rotate on the seat. The seating surface, as shown by the transferred marking compound,

should have good contact all the way around.

Apply the abradant to the valve seat face, suitable for running in when rotating valve seat

with valve seat cutter.

After reassembling, check the valve clearance.

0.8mm

Содержание Y173V



































































Результаты поиска

Содержание Y173V

Отзывы:

Похожие инструкции для Y173V

Бренды по названию

Популярные бренды

Cobra Y173V, Руководство по обслуживанию

Результаты поиска

Содержание Y173V

Отзывы:

Похожие инструкции для Y173V

Бренды по названию

Популярные бренды