Cobra Y173V Скачать руководство пользователя страница 18

Страница: 18 / 66

3. MAINTENANCE

THROTTLE VALVE

GOVERNOR SUPPORT

GOVERNOR ARM

NUT M6

Clearance too big: Intake and exhaust valve opening delay will shorten the intake and

exhaust time, lower the opening height of the valve and change normal distributing phase to

result in power lowering from the intake lack and exhaust uncompleted. Furthermore, also

make vale train parts knock increasing and wearing quickly.

Clearance too small: After running, engine parts will be heated to expand and push the valve

open, which will make the engine not closing tight and result in leaking, power lowering,

serious carbon deposit or burn on the valve surface, even valve impacting the piston.

3-7

Governor

Governor
adjustment

Remove the air cleaner.

Loosen the nut (M6). Be sure that

the carburetor throttle valve is

fully open.

Rotate the governor support shaft

fully to the right (governor fully

closed position), and tighten the

nut.

TORQUE VALUE: 10-12N.m

Check to see that the governor support and throttle valve move freely.

Check the maximum engine speed

Maximum Speed Adjustment

Start the engine and allow it to warm up to normal operating temperature.

If the maximum speed not conforming to specified value, adjust the adjusting bolt

30.

Engine maximum speed

：

2850±100rpm

Speed too big

Turn the bolt counterclockwise.

Speed too small

Turn the bolt clockwise

Содержание Y173V



































































Результаты поиска

Содержание Y173V

Отзывы:

Cobra Y173V, Руководство по обслуживанию, Страница: 18 / 66

Результаты поиска

Содержание Y173V

Отзывы: