Cobra Y173V Скачать руководство пользователя страница 20

Страница: 20 / 66

4. DISASSEMBLING AND SERVICING

TROUBLE

CAUSE

REMEDY

ess

ion

uel

ppl

ug.

Piston ring is worn to or even over its

wear limit

Replace

Piston ring is broken.

Replace

Piston ring is sticking.

Clear up carbon fouling.

Spark plug is not installed tighten or

without a gasket.

Tighten with a gasket in.

Air leakage between cylinder block

and cylinder head.

Check cylinder gasket, and the flatness of the

surface by which cylinder block contacting with

cylinder head

Tighten cylinder head bolts in stipulated order to

stipulated torque.

Air leakage in the valves

Check valve. Clearance and tightness, repair if

necessary.

If still can’t starting, have the engine to our authorized dealer for repairing.

●

Spark plug testing



Make sure there is no spilled fuel outside the engine and that the spark plug isn’t

dipped with fuel.



When testing the spark plug, never hold the high- tension line of the spark plug

with wet hand.



To prevent fire, keep sparks far away from the spark plug mounting hole.

SPARK PLUG,SPARK PLUG CAP

RECOL STARER GRIP

Содержание Y173V



































































Результаты поиска

Содержание Y173V

Отзывы:

Cobra Y173V, Руководство по обслуживанию, Страница: 20 / 66

Результаты поиска

Содержание Y173V

Отзывы: