Cobalt Digital Inc 9903-UDX-ADDA Скачать руководство пользователя страница 21

Страница: 21 / 100

9903UDXADDA-OM (V1.5)

9903-UDX-ADDA PRODUCT MANUAL

1-17

Introduction

Technical Specifications

Serial Digital Video Input (cont.)

SDI Receive Cable Length: 3G/HD/SD: 120/180/320 m (Belden
1694A)

SDI Return Loss: >15 dB up to 1.485 GHz; >10 dB up to
2.970 GHz

SDI Alignment Jitter: 3G/HD/SD: < 0.3/0.2/0.2 UI

Timing Jitter: 3G/HD/SD: < 2.0/1.0/0.2 UI

Note: SDI Return loss and receive cable length are affected by
rear I/O module used. Specifications represent typical
performance.

Analog Video Input

Number of Inputs:

One SD analog CVBS; 3-connector YPbPr component. CVBS
can be upscaled to any supported SDI format; all SDI formats
can be downconverted to CVBS.

Impedance: 75

Ω

ADC resolution: 10-bit

Sampling frequency: 54 MHz (4x over-sampling SD)

SD Y/C separation: 5 line Adaptive Comb Filter

SD Freq. Response: ± 0.25 dB to 5.5 MHz

SD SNR: > 55 dB to 5.5 MHz (unweighted)

Differential Phase: < 1 degree

Differential Gain: < 1%

Nonlinearity < 1%

HD Freq. Response: Y 30 MHz., PbPr 15 MHz

HD SNR: > 55 dB to 30 MHz (unweighted)

AES Audio Inputs

Standard:

SMPTE 276M

Number of Inputs:

Up to 16 unbalanced; AES-3id

Impedance:

Ω

Analog Audio Inputs

Number of Inputs:

Two balanced using 3-wire removable Phoenix connectors;
0 dBFS => +24 dBu

Analog Input Impedance: >10 k

Ω

Analog Reference Level: -20 dBFS

Analog Nominal Level: +4 dBu

Analog Input Clip Level: +24 dBu (0 dBFS)

Analog Freq. Response: ±0.2 dB (20 Hz to 20 kHz)

Analog SNR: 115 dB (A weighted)

Analog THD+N: -96 dB (20 Hz to 10 kHz)

Analog Crosstalk: -106 dB (20 Hz to 20 kHz)

Table 1-1

Technical Specifications — continued

Item

Characteristic

Содержание 9903-UDX-ADDA





































































































Результаты поиска

Содержание 9903-UDX-ADDA

Отзывы:

Похожие инструкции для 9903-UDX-ADDA

Бренды по названию

Популярные бренды

Cobalt Digital Inc 9903-UDX-ADDA, Руководство по эксплуатации продукта

Результаты поиска

Содержание 9903-UDX-ADDA

Отзывы:

Похожие инструкции для 9903-UDX-ADDA

Бренды по названию

Популярные бренды