Cobalt Digital Inc 9903-UDX-ADDA Скачать руководство пользователя страница 97

Страница: 97 / 100

9903UDXADDA-OM (V1.5)

9903-UDX-ADDA PRODUCT MANUAL

3-65

Operating Instructions

Troubleshooting

Figure 3-10 SD Card Installation

(See Figure 3-11.) With card powered-down, locate the

MMC BOOT

button on the card. Proceed as shown in picture.

Figure 3-11 MMC Boot Button

With button now released, the card will begin reprogramming:

•

COM

LED illuminates and remains illuminated.

•

When reprogram is complete,

COM

LED turns off, on, and then off

again (entire process takes about 1-1/2 minute).

From underside of card, locate
the SD card receptacle

With SD card labeling facing up
(as shown), gently push the
card into the receptacle until it
clicks and locks into place

Electronic device or assembly is susceptible
to damage from an ESD event. Handle only
using appropriate ESD prevention practices.

Press and hold MMC BOOT button

FRONT OF CARD

Power-up card and continue holding
button for 3 seconds, then release
button

COM LED

Содержание 9903-UDX-ADDA





































































































Результаты поиска

Содержание 9903-UDX-ADDA

Отзывы:

Похожие инструкции для 9903-UDX-ADDA

Бренды по названию

Популярные бренды

Cobalt Digital Inc 9903-UDX-ADDA, Руководство по эксплуатации продукта

Результаты поиска

Содержание 9903-UDX-ADDA

Отзывы:

Похожие инструкции для 9903-UDX-ADDA

Бренды по названию

Популярные бренды