40
PREPARATION
• Whenever possible, mount drawer and basket slides to the vertical
partitions before tower assembly, i.e. before positioning the
partitions in the closet, while the partitions are lying on the floor.
(See FIG. 1)
• However, slides can be attached to up-right shelf tower partitions
when in final position in the closet. Have your pieces ready to
set together.
• We’re reminding you to carefully plan the number of cuts and the
number of pieces re-quired for any given closet design with crown
molding. You must consider minor waste factor for lengths you
cannot use,and you must consider for seaming (discussed later in
these instructions) on any molding lengths of approximately 8 feet
or longer.
• Baskets must have one fixed shelf installed above and one below a
bank of baskets to ensure roll smoothly in slide track.
• Baskets should not be installed higher than 48 in. from the floor.
Most installations will position the top fixed shelf at 42 in. from
the floor.
• To determine slide location, use the spacing guide (next page) to
calculate how many holes to count before installing each
basket slide.
INSTALLATION
1. To install slides, first pull black plastic fitting up
(FIG. 2A)
to
release inner slide from extension slides. Second, remove inner
slide
(FIG. 2B)
and attach it to the partition using two (2) Euro
screws per slide.
(See FIG. 3)
2. Reattach extensions onto inner slides.
(See FIG. 3)
3. After mounting all slides in place and positioning the shelving
tower(s) in final location, hang basket(s) on clips/hooks
(FIG. 4)
from second (lower) rim of basket. (
FIG. 5
shows close up of clip/
hook on basket rim. Clip/hooks have plastic removable “stays” to
hold baskets in place on hook.)
4. After mounting all slides in place and positioning the shelving
tower(s) in final location, hang basket(s) on clips/hooks
(FIG. 4)
from second (lower) rim of basket. (
FIG. 5
shows close up of clip/
hook on basket rim. Clip/hooks have plastic removable “stays” to
hold baskets in place on hook.)
Basket
ACCESSORY ASSEMBLY
DESCRIPTION
Basket (6 in., 11 in. or
17 in.)
Slides
Euro Screws
PARTS
QTY
1
2
4
Back Panels
Shelving /Towers
Drawers and Doors
Adjustable Shelves
Molding
}
Baskets, Valet Rods,
Tie & Belt Racks, and
other accessories
Islands
Benches
ORDER OF ASSEMBLY
Содержание MasterSuite
