14
Hanging Tower System
SHELVING/TOWER ASSEMBLY
INSTALLATION
1. Draw a level line across the entire wall at 82-7/8 in. or 93 in.
from the floor.
2. Locate and mark the wall studs along your line.
(See FIG. 2)
3. Measure from a corner of the closet wall to the center of the
first stud. Next, measure the same distance (e.g. 8-1/2 in.) from
the end of the rail. If the measured distance does not fall exactly
on a rail hole
(See FIG. 3)
, you must trim the end of the rail the
length necessary to ensure the holes align with the wall studs.
(Holes are pre-drilled on 1 in. centers along the length of the rail.
Studs should fall on 16 in. or 24 in. centers.) Use a hacksaw and
file to cut and de-burr a length of rail as necessary.
Rail and Cover
Cleat (for each “center” tower)
#10 x 2 in. Washer Hex Head
Screws
Left and Right Brackets
Fast Caps
Hanging Partitions (any length
with at least one 80 in. or 60 in.
thru-drilled panel)
Cam Fixed Shelves
Screw-in Studs (#56544)
Double-Sided Studs (#56534)
Zip Toggle Bolts
#8 x 1-1/4 in. Screws
#8 x 5/8 in. Screws
Angle (Corner) Brackets
Easy Anchors
PARTS
PREPARATION
Installation of a MasterSuite Hanging System and related sections
requires skill and familiarity with the installation of the floor-
mounted shelf tower and its related components.
The rail-mounted hanging closet system relies upon correct
anchoring of the rail to the wall supports, proper cleat assembly, and
mounting of the brackets to the partitions to bear the considerable
weight of the system. Accurate fastening of these components is
essential to ensuring the system is safely and permanently secured.
We also recommend that any panel that is adjacent to a side wall be
secured to that side wall at a stud location.
• Ensure the hanging vertical partitions do not require trimming
to fit above the closet’s baseboard. Ensure the closet height is
sufficient to accommodate use of your screw gun to install the
top shelf if the design uses a continuous top shelf piece. You may
need to shorten, or notch the partitions to fit above, or around,
the baseboard.
• Mount all left and right suspension brackets to the hanging
partitions prior to system installation using two (2) #8 x 5/8 in.
screws through the bracket into the pre-drilled bracket holes
on the partition. Snap on Fast Caps to the opposite side of the
partition over the exposed bracket holes.
(See FIG. 1)
• Mount all drawer and basket runners, if desired, prior to hanging
partitions on the rail. (See “Drawer” or “Basket” assembly
sections for instructions regarding runner installation.)
Back Panels
}
Shelving /Towers
Drawers and Doors
Adjustable Shelves
Molding
Baskets, Valet Rods,
Tie & Belt Racks, and
other accessories
Islands
Benches
ORDER OF ASSEMBLY
Содержание MasterSuite
