28
Drawer
DOOR & DRAWER ASSEMBLY
DESCRIPTION
Drawer (face, bottom,
back and side panels)
Drawer Runners (left
and right)
Cam locks
(6 in. H = 2; 10 in. H = 4)
Screw-in Studs
(6 in. H = 2; 10 in. H = 4)
#6 x 1/2 in. Screws (for
14 in. or 18 in. deep
drawers)
Euro Screws
Drawer Handle
(with included
handle hardware)
#8 x 1-1/4Ó Phillips
Head Screws
14 in. or 18 in. Slide
Template (#05-90052
or #05-90053)
PARTS
QTY
1
2
2 or 4
2 or 4
2 or 6
4
1
4
1
PREPARATION
• Whenever possible for greatest leverage, mount drawer runners
to the side panels (partitions) while panels are lying on the floor
(before side panels are mounted in the closet).
• Similar to basket installation, drawers re-quire mounting one fixed
shelf above and one below the rack of drawers for stability.
• Drawers (and baskets) should never be mounted behind
overlapping sliding doors or in locations where an open drawer
may bump into another obstacle.
INSTALLATION
1. Attach drawer sides to drawer back with four (4) #8 x 1-1/4 in.
Phillips Head Screws.
(See FIG. 1)
2. Insert the drawer bottom into the slot along the bottom of the
drawer sides.
(See FIG. 2)
Push the cam locks into the holes in the
drawer sides. Be sure to orient cams so that the open end of the
cam faces the hole in the front edge.
3. Locate your selected drawer front(s). Choose your handle size and
drill a 1/16 in. pilot hole through each corresponding dimple on
the back of the drawer front. Turn the drawer front over and drill a
3/16 in. hole for handle at pilot location(s).
NOTE:
It is important to drill both the pilot hole through the back
and the regular hole through the front to prevent chipping.
4. Attach the drawer handle. (Three sizes of screws are supplied to
accommodate drawer front styles.)
(See FIG. 3)
5. Thread 2 (or 4 for 10 in. drawer) screw-in studs to drawer
front. Attach drawer front to drawer assembly. Use a Phillips
screwdriver to tighten cam locks.
For 14 in. D drawers, use two #6 x 1/2 in. wood screws to attach
each drawer runner to a drawer side.
For 18 in. D drawers, use three #6 x 1/2 in. wood screws.
6. Place 14 in. or 18 in. Slide template into partition holes (so arrow
points forward) at desired drawer runner location. Use a 5mm
Self-Centering Drill Bit to drill holes as marked in template. Attach
each drawer runner to partition with two (2) Euro screws.
Back Panels
Shelving /Towers
}
Drawers and Doors
Adjustable Shelves
Molding
Baskets, Valet Rods,
Tie & Belt Racks, and
other accessories
Islands
Benches
ORDER OF ASSEMBLY
Содержание MasterSuite
