Climecon CLEANMASTER Series Скачать руководство пользователя | Manualshive

Страница: 9 / 27

background image

climecon.fi

9

Lämmittäjänkatu 4 A, 00880 Helsinki, FINLAND · Tel. +358 (0)20 198 6600

© Climecon

6. Electrical connections of the CleanMaster hood

Danger of electric shock!
Electricity supply to the control device

NOTE! Electrical connections may only be made by a professional electrician.

- The hood has to be electrified through the safety switch, which is visible near the hood and has

been named

- The control device’s switching power is max. 400 W
- The light is connected to the light group (connection cable as factory equipment)

Electricity supply connections:

Q1:2 (wire protection) - 230 VAC IN, 50 Hz, L

Q1:4 (wire protection) - 230 VAC IN, 50 Hz, N

X2: PE (left) 230 VAC IN, 50 Hz, PE

Electricity supply is brought to the casing through a strain

reliever. Note, the opened hatch may turn.
Electricity supply has to be connected to the hood/hood

group via a safety switch.
The safety switch has to be clearly visible and the label

included in the delivery must be attached to it!

!

CleanMaster

huuvan/ilmanvaihtokaton turvakytkin

hood/ventilation ceiling safety switch

Katkaise virta AINA ennen

huollon aloittamista.

before maintenance.

climecon.fi/clm

«
...
7
8
9
10
11
...
»

Содержание CLEANMASTER Series




























Отзывы:

Нет отзывов

Похожие инструкции для CLEANMASTER Series

Бренд: Venduro Страницы: 44

Бренд: Rangemaster Страницы: 36

Бренд: Gaggenau Страницы: 32

Бренд: Zephyr Страницы: 56

Бренд: Xo Страницы: 33

tastic LUMINATE 34401

Бренд: IXL Страницы: 2

Бренд: Proline Страницы: 10

Glide EGL-E30AS

Бренд: Zephyr Страницы: 21

Бренд: CDA Страницы: 12

Бренд: Nordmende Страницы: 20

Бренд: Faber Страницы: 104

Бренд: Bauknecht Страницы: 12

Бренд: NuTone Страницы: 28

Avanzare - DX 9907

Бренд: Modena Страницы: 32

Бренд: arietta Страницы: 32

Бренд: Smeg Страницы: 12

Бренд: Smeg Страницы: 17

Бренд: Vesta Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды