Climax H&S TOOL SPEED FACER ODF100 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 132

background image

P/N 102615, Rev. 0

Page 51

5. Treat the cable end with solder to prevent fray-

ing and the possibility of coming loose (see Fig-
ure 5-11).

6. Feed the cable end under the head of the M4

screw and tighten (see Figure 5-11).

7. Check for free movement of the mechanism by

actuating the tripper arm (the feed adjustment
screw may need advanced out). If interference
is observed with cable end and the feedbox
wall, bend the cable end away from the head of
the M4 screw.

8. Secure the protective cable conduit with the

Velcro straps.

F

IGURE

5-11. S

OLDER

-

TREATED

CABLE

END

(

LEFT

);

CABLE

END

SECURED

UNDER

THE

M4

SCREW

(

RIGHT

)

5.4

T

ROUBLESHOOTING

This section is intended to help you solve basic machine
performance problems. For serious maintenance or if
you have questions on the following procedures, contact
H&S.

5.4.1

The machine isn’t turning

If the machine is not rotating, check the following:

1. The power source is connected and energized

(hydraulic motor powered units only).

2. The

EMERGENCY

STOP

is reset (Section 4.3.1 on

page 42 and Sectio n 5.3.3 on page 47).

3. The air regulator is open and not broken (Figure

4-6 on page 42).

4. There is air pressure entering and leaving the

Air Caddy. Check the air pressure by disconnect-
ing the hose quick disconnects and checking for
air bleed (Figure 4-6 on page 42).

5. All the valves are open (Figure 4-6 on page 42).
6. All the quick disconnects are fully engaged (Fig-

ure 4-6 on page 42).

7. Check machine movement by first checking that

the power to the machine drive is isolated and
locked out, then by manually rotating the
machine using the lifting eyes on the bridge
weldment.

5.4.2

The machine isn’t feeding

If the machine isn’t feeding properly, check the follow-
ing:

1. The feed trippers are engaged (Section 3.4.7 on

2. The feed direction knob is either pushed in or

pulled out, not in the neutral center position.

3. The feed cable has not been disconnected from

either the tripper or the feedbox.

5.4.3

The machine is performing poorly

If the machine is performing poorly, check the follow-
ing:

1. The tool is installed correctly (Section 3.4.4 on

2. The machine is tight to the workpiece (Section

3. on page 30).

3. The bridge weldment screws are secure.
4. The locking gib screws on the radial and axial

slides are adjusted correctly (Section 4.2.1 on
page 39 and Section 4.2.2 on page 40).

5. The swivel clamping screws on the rotating tool

head are tight (Section 3.4.3 on page 34).

6. The cutting tool or insert is sharp and has the

correct geometry for the material and type of
cut.

7. The speed and feed rates are set correctly. If

necessary, experiment with different speeds
and feed rates. Typically, slower speeds and
shallower cuts produce less tool chatter.

8. If the machine has been running for at least an

hour, the roller bearings may require lubrica-
tion.

«
...
67
68
69
70
71
...
»

Содержание H&S TOOL SPEED FACER ODF100





































































































































Отзывы:

Нет отзывов

Похожие инструкции для H&S TOOL SPEED FACER ODF100

Бренд: ABB Страницы: 86

Бренд: Canta Страницы: 2

Бренд: PANDROL Страницы: 36

Бренд: Federal Signal Corporation Страницы: 12

Бренд: Raymarine Страницы: 124

Бренд: Raymarine Страницы: 192

Бренд: K-LASER Страницы: 70

Бренд: K-LASER Страницы: 72

Бренд: Rapala Страницы: 14

Бренд: S.R.Smith Страницы: 43

Бренд: Landoll Страницы: 70

Бренд: Landice Страницы: 19

Бренд: Landice Страницы: 7

Chicken Coop Plan 3x5

Бренд: EASY COOPS Страницы: 21

Chicken Coop Plan 4x6

Бренд: EASY COOPS Страницы: 18

Chicken Coop Plan 8x10

Бренд: EASY COOPS Страницы: 18

Бренд: Igema Страницы: 22

Бренд: MAGSTIM Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды