Climax H&S TOOL SPEED FACER ODF100 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 132

background image

P/N 102615, Rev. 0

Page 53

6

STORAGE AND SHIPPING

IN THIS CHAPTER:

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -53

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -53

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -53

- - - - - - - - - - - - - - - - - - - - - - - - - - -53

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -55

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -58

6.1

S

TORAGE

WARNING

If not properly secured, this machine can fall and
cause fatal injuries to personnel. Pay special
attention to vertical flange and overhead mounting
installations.
The machine must be properly rigged and attached
to a crane or other suitable lifting apparatus before
beginning any disassembly steps.

Proper storage of the ODF Speed Facer will extend its
usefulness and prevent undue damage.
Before storing, do the following:

1. Clean the machine with solvent to remove

grease, metal chips, and moisture.

2. Drain all liquids from the pneumatic condition-

ing unit.

Store the ODF Speed Facer in their original shipping
container. Store the ODF80 and larger Speed Facers on
the supplied inclined shipping frame. Keep all packing
materials for repackaging the machine.

6.1.1

Short-term storage

Do the following for short-term storage (three months
or less):

1. Remove all tooling.
2. Remove the motor and hoses.
3. Clean the machine to remove dirt, grease,

metal chips, and moisture.

4. Spray all unpainted surfaces with LPS-2 to pre-

vent corrosion.

5. Store the ODF70 and smaller models in their

original shipping box (see Figure 6-8 on page
57).

6. Store the ODF80 and larger Speed Facers on

their shipping frame (see Figure 6-9 on page 58)
and store all accessories in the toolbox.

6.1.2

Long-term storage

Do the following for long-term storage (longer than
three months):

1. Follow the short-term storage instructions, but

use LPS-3 instead of LPS-2.

2. Add a desiccant pouch to the shipping container

or toolbox. Replace according to manufacturer
instructions.

3. Store the shipping container or shipping frame

in an environment out of direct sunlight with
temperature < 70ºF (21ºC) and humidity < 50%.

6.1.3

Storing the ODF80 and larger
models

Do the following to store the ODF80 and larger models:

1. Rig the machine using the two lifting eyes as

shown with squircle 1 in Figure 6-9 on page 58.

2. Lift the machine so it is hanging vertical.

«
...
69
70
71
72
73
...
»

Содержание H&S TOOL SPEED FACER ODF100





































































































































Отзывы:

Нет отзывов

Похожие инструкции для H&S TOOL SPEED FACER ODF100

Бренд: Labnet Страницы: 2

Бренд: Jacobs Ladder Страницы: 16

Бренд: Bang & Olufsen Страницы: 2

Бренд: NANLUX Страницы: 39

Бренд: Garmin Страницы: 10

Бренд: Naviom Страницы: 31

Бренд: HABYS Страницы: 16

Бренд: Taurus Страницы: 24

Бренд: York Страницы: 26

Бренд: Ultrasport Страницы: 72

Бренд: Wieland Страницы: 2

41370 Micro Spot

Бренд: SHOWTEC Страницы: 22

Бренд: Carestream Страницы: 64

Бренд: RAM Страницы: 4

Ti-Max NLX nano

Бренд: NSK Страницы: 38

Бренд: Sensio Страницы: 3

Biosafe 110 Port

Бренд: Sartorius Страницы: 2

Бренд: Fri-Jado Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды